Harmony 3 peripheral library application examples for SAM HA1 family

MPLAB® Harmony 3 is an extension of the MPLAB® ecosystem for creating embedded firmware solutions for Microchip 32-bit SAM and PIC® microcontroller and microprocessor devices. Refer to the following links for more information.

This repository contains the MPLAB® Harmony 3 peripheral library application examples for SAM HA1 family

To clone or download these applications from Github, go to the main page of this repository and then click Clone button to clone this repository or download as zip file. This content can also be downloaded using content manager by following these instructions.

Contents Summary

Folder	Description
apps	Contains peripheral library example applications
docs	Contains documentation in html format for offline viewing (to be used only after cloning this repository onto a local machine). Use github pages of this repository for viewing it online.

Code Examples

The following applications are provided to demonstrate the typical or interesting usage models of one or more peripheral libraries.

Name	Description
AC Sleepwalking	This example application shows how to use the AC Peripheral library to perform a single shot comparison in standby sleep mode periodically and wake up the device at the end of a successful comparison
AC PWM generation	This example application shows how to use the Analog Comparator Peripheral library to generate a 1KHz PWM waveform
ADC Sample	This example application shows how to sample an analog input using the ADC and displays the converted samples on a serial terminal
ADC window sleepwalking	This application shows how to configure ADC in a sleepwalking operation, where input voltage is measured at a fixed interval, but device is not woken from sleep until the measured value is below a given threshold
Clock configuration	This example application shows how to configure the clock system to run the device at maximum frequency. It also outputs a prescaled clock signal on a GPIO pin for measurement and verification
DAC waveform generation	This example application shows how to use the DAC to generate a 1 KHz Sine or Sawtooth wave with a lookup table
DAC waveform generation with DMA	This example application shows how to use the DAC with the DMA to generate a 5 KHz sinusoidal waveform without CPU intervention
DMAC memory transfer	This example application demonstrates how to use the DMAC peripheral to do a memory to memory transfer
DSU compute CRC32	This example application demonstrates how to use the DSU Peripheral library to compute 32-bit Cyclic Redundancy Checksum (CRC)
EIC Interrupt	This example application demonstrates how to generate interrupt using the EIC on switch press and indicate it through an LED
NVMCTRL read write	This example application demonstrates how to use the NVMCTRL to erase and program the internal Flash memory
PM wakeup using EIC	This application demonstrates entering the low power modes and exiting it using the EIC
PORT polling	This example application demonstrate how to poll the switch input, and indicate the switch status using the LED
RTC alarm interrupt	This example shows how to use the RTC to configure the time and generate the alarm
RTC periodic interrupt	This example application shows how to use the RTC to generate periodic interrupts
SERCOM I2C EEPROM read write	This example application demonstrates how to use the SERCOM peripheral to write and read from the I2C serial EEPROM memory
SERCOM SPI EEPROM read write	This example application demonstrates how to use the SERCOM SPI peripheral to write and read from the SPI serial EEPROM memory
SERCOM SPI interrupt	This example application shows how to use SERCOM SPI PLIB with external loop back to write and then read back an array of data in interrupt mode
SERCOM USART interrupt	This example application demonstrates how to use the SERCOM peripheral in USART mode to transfer data in a non-blocking manner
SERCOM USART ring buffer	This example application demonstrates how to use the SERCOM peripheral in USART ring buffer mode to transfer data in a non-blocking manner
Systick periodic interrupt	This example shows how to use the SysTick to generate periodic interrupts
TC capture mode	This example shows how to use the TC module in capture mode to measure duty cycle and frequency of an external input
TC compare mode	This example shows how to use the TC module in compare mode to generate an active low, active high, and toggle output on compare match
TC timer mode	This example shows how to use the TC module in timer mode to generate periodic interrupt
TCC PWM generation	This example application shows how to use the TCC to generate a 2 or 3 phase PWM signals for motor control with dead time
WDT timeout	This example shows how to generate a Watchdog timer reset by emulating a deadlock